The last person to post in this thread don’t get nothing.

[Justsomedude]

Im not sure that I know exactly what you mean but I just tried them in my shop. Fired 2 rounds and they work fantastic.

[GrapeApe]

I THINK he's worried about chain fires

[Justsomedude]

I THINK he's worried about chain fires

Ah, I see. I actually watched a video about that the other day and a guy was testing all of the ways that chain fires happen. It was obvious after his testing that they never happen at the rear of the cylinder. It's always the front.

[Chiro1989]

OK, I am not familiar with cap and ball revolvers, I was worried about chain fires , I assume gasses don't come back through the nipple?

[CPJ 2.0]

OK, I am not familiar with cap and ball revolvers, I was worried about chain fires , I assume gasses don't come back through the nipple?

Even metal caps are basically obliterated during firing. There’s really no danger from using plastic if anything it would probably be safer so that you are not spitting out little pieces of metal.

[bullsi1911]

That is pretty cool. Never thought about using 3D printing for that

[CPJ 2.0]

The best part….hes using a robot to do his work.

[Justsomedude]

OK, I am not familiar with cap and ball revolvers, I was worried about chain fires , I assume gasses don't come back through the nipple?

Even metal caps are basically obliterated during firing. There’s really no danger from using plastic if anything it would probably be safer so that you are not spitting out little pieces of metal.

Yep, and they split almost identical to regular percussion caps. I'm pleasantly surprised with how well they work because it's just my luck to get into a hobby that is missing a major component to make it work , and there is the gratification of letting a robot do my dirty work.

[CPJ 2.0]

Practice blade is in the easy bake oven. Doesn’t seem to be to hard to apply. Stupid easy, really.
The trick is not touching it and getting it into the oven.
The good thing if you do touch it (before you heat it) you just blow it off with the air gun and start over.

[CPJ 2.0]

Yep. Super happy with the results for a first go. Learned some stuff.

[Justsomedude]

[Diver43]

Yep. Super happy with the results for a first go. Learned some stuff.

Looks like you learned how to make a good knife. When does sales production start?

[CPJ 2.0]

Yep. Super happy with the results for a first go. Learned some stuff.

Looks like you learned how to make a good knife. When does sales production start?

Soonish.

[Justsomedude]

But seriously those are pretty damn sexy. I think you found a legit side hustle.

[CPJ 2.0]

But seriously those are pretty damn sexy. I think you found a legit side hustle.

Thanks.
I’d like to finally make/sell something that pays for itself AND pays me back.

[Zee]

I like it!

[Rugerfan]

What they said!!!

I really like that!!

[Chiro1989]

Need to come up with a catchy name to billboard on the handle

[CPJ 2.0]

Need to come up with a catchy name to billboard on the handle

I’m thinking of engraving “Deez Nutz” on the side.

[jbp-ohio]

Need to come up with a catchy name to billboard on the handle

I’m thinking of engraving “Deez Nutz” on the side.

To/too/two/tutu common.

[CPJ 2.0]

Need to come up with a catchy name to billboard on the handle

I’m thinking of engraving “Deez Nutz” on the side.

To/too/two/tutu common.

Z’s nutz.

[jbp-ohio]

I’m thinking of engraving “Deez Nutz” on the side.

To/too/two/tutu common.

Z’s nutz.

Better

[Diver43]

I’m thinking of engraving “Deez Nutz” on the side.

To/too/two/tutu common.

Z’s nutz.

[Chiro1989]

FAFO, CST (cuttystabbything), LMAOE (leavemealoneorelse), PDPS (pigsdeerpeoplestuff)

[N454casull]

Yep. Super happy with the results for a first go. Learned some stuff.

You can laser engrave those super easy.