Guns & Outdoors Forum

Posted: **Tue Jun 04, 2024 12:22 am**

Boring bar it is. Besides, I'm impatient and don't want to wait for the reamer to show up.

Posted: **Tue Jun 04, 2024 12:47 am**

Justsomedude wrote: ↑Tue Jun 04, 2024 12:22 am Boring bar it is. Besides, I'm impatient and don't want to wait for the reamer to show up.

I mean, it’s the sprit of the Fcg 9.

Hell, use an endmill as a boring bar.
(That actually works good )

Posted: **Tue Jun 04, 2024 1:02 am**

I broke the rear sight on my air rifle a couple months ago. The Grinny's have been getting bold since it has been out of commission. Standing on my retaining blocks and mocking me.

I have a cheap Tasco Rimfire scope I got on sale last year. Mounted it Saturday and sighted it in. Five Grinny's in six shots....

: 20240603_173459.jpg (4.22 MiB) Viewed 1605 times

Posted: **Tue Jun 04, 2024 1:28 am**

CPJ 2.0 wrote: ↑Tue Jun 04, 2024 12:47 am
Justsomedude wrote: ↑Tue Jun 04, 2024 12:22 am Boring bar it is. Besides, I'm impatient and don't want to wait for the reamer to show up.
I mean, it’s the sprit of the Fcg 9.

Hell, use an endmill as a boring bar.
(That actually works good )

You make a good point. Thankfully I have a good selection of boring bars, thanks to the inheritance of all of my dad's tooling but some of them I've ground myself from hss blanks for odd jobs. The strangest use (or misuse) of a tool was single point threading with a small tap because I was too lazy to grind one

. Worked good though.

Posted: **Tue Jun 04, 2024 6:39 pm**

Chamber cut. I ended up using a small boring bar after looking up Saami specs and finding the case taper. It turned out great.

: 20240604_143736.jpg (2.85 MiB) Viewed 1586 times

Posted: **Thu Jun 06, 2024 10:09 pm**

What a pain in the ****. Apparently you're supposed to drill the firing pin hole before joint the two metal rods together which most people do with a hand drill. Yeah right. Even so, after having them welded together it wouldn't fit the 4 jaw chuck in the lathe because of the offset and I didn't feel like making a fixture so I got creative.

: 20240606_154028.jpg (3.11 MiB) Viewed 1562 times

It worked out really well and left me with a nice drilled and reamed hole.
I ended up getting it finished but will have to test fire it at work tomorrow.

: 20240606_175417.jpg (7.67 MiB) Viewed 1562 times

: 20240606_175424.jpg (3.24 MiB) Viewed 1562 times

: 20240606_175435.jpg (7.02 MiB) Viewed 1562 times

Posted: **Thu Jun 06, 2024 10:29 pm**

Posted: **Sat Jun 08, 2024 12:57 am**

Well it works, and works well too! I get perfect primer strikes because instead of using the 3d printed template guide to hand drill the firing pin channel, I found the dead center to where the pin needs to be by making a hardened center punch that fit the bore and assembled it to punch the bolt. And it absolutely throws the cases out really good for a gun without an extractor. And now it'll go in the safe with the rest of the stuff I own and never shoot.

Posted: **Sat Jun 08, 2024 1:29 am**

Cool project

Posted: **Sat Jun 08, 2024 2:03 pm**

Nicely done hey, needs a red dot, bayonet mount if you want to go full Redneck

Posted: **Sat Jun 08, 2024 2:18 pm**

Neat to see it come together.

Kinda neat to have something functional nearby that only exists because you make stuff.

Posted: **Sat Jun 08, 2024 4:34 pm**

One good thing about leasing. My wifes lease is up on her Range Rover. So..... you just get another one.

: 20240608_123211.jpg (3.28 MiB) Viewed 1504 times

Posted: **Tue Jun 11, 2024 12:13 am**

That ain’t a .020 deep cut.

Thankfully I’m fast-ish on the stop button.

Posted: **Wed Jun 19, 2024 12:53 am**

An actual song from 1942

https://youtu.be/-qHW883ypzY?si=yx1dosSZWqniWTju

Posted: **Wed Jun 19, 2024 10:31 am**

My older brother used to sing that to our grandmother, she loved it.
I preferred "Grandma got run over by a reindeer"

Posted: **Sat Jun 22, 2024 4:15 am**

Well, we got ourselves a hockey tournament, go Oilers

Posted: **Sat Jun 22, 2024 11:39 pm**

jbp-ohio wrote: ↑Sat Jun 08, 2024 4:34 pm One good thing about leasing. My wifes lease is up on her Range Rover. So..... you just get another one.

20240608_123211.jpg

Big fan of leasing, especially when you can write it off your business

Nice wheels!

Posted: **Wed Jul 03, 2024 9:59 pm**

Been wanting to make an ER40 collet chuck for my small 10x30 benchtop lathe for a while. I used to use mostly the 3 jaw chuck for it because it had .0003 runout over 6 inches but the jaws got bell mouthed. I typically keep my 4 jaw in my 14x40 lathe for indicating barrels and larger stuff because it has a 2.25 inch spindle bore. Anyhow, ordered a piece of 1045 from ebay and got started on it yesterday and finished today. It has absolutely zero runout since I machined it on the spindle. I'll use the hell out of this thing.

: 20240703_161427.jpg (2.72 MiB) Viewed 1225 times

: 20240703_161435.jpg (3.16 MiB) Viewed 1225 times

Posted: **Sat Jul 06, 2024 5:10 am**

The new Beverly Hills Cop movie on Netflix is worth the watch, good to see Eddie Murphy having fun.

Posted: **Sun Jul 07, 2024 4:06 am**

And the new Guy Ritchie movie on Netflix, The Gentleman, is excellent, quite the cast

Posted: **Sun Jul 07, 2024 3:06 pm**

Justsomedude wrote: ↑Wed Jul 03, 2024 9:59 pm Been wanting to make an ER40 collet chuck for my small 10x30 benchtop lathe for a while. I used to use mostly the 3 jaw chuck for it because it had .0003 runout over 6 inches but the jaws got bell mouthed. I typically keep my 4 jaw in my 14x40 lathe for indicating barrels and larger stuff because it has a 2.25 inch spindle bore. Anyhow, ordered a piece of 1045 from ebay and got started on it yesterday and finished today. It has absolutely zero runout since I machined it on the spindle. I'll use the hell out of this thing.
20240703_161427.jpg
20240703_161435.jpg

Collet chucks can NOT be beat as long as you can turn whatever run out the stock has out before you get to the final diameter. Just like a 3 jaw.
But the repeatability is sooooo much better than a three jaw. More importantly, you don’t foul up the part finish with the collet.

Posted: **Sun Jul 07, 2024 6:48 pm**

CPJ 2.0 wrote: ↑Sun Jul 07, 2024 3:06 pm
Justsomedude wrote: ↑Wed Jul 03, 2024 9:59 pm Been wanting to make an ER40 collet chuck for my small 10x30 benchtop lathe for a while. I used to use mostly the 3 jaw chuck for it because it had .0003 runout over 6 inches but the jaws got bell mouthed. I typically keep my 4 jaw in my 14x40 lathe for indicating barrels and larger stuff because it has a 2.25 inch spindle bore. Anyhow, ordered a piece of 1045 from ebay and got started on it yesterday and finished today. It has absolutely zero runout since I machined it on the spindle. I'll use the hell out of this thing.
20240703_161427.jpg
20240703_161435.jpg
Collet chucks can NOT be beat as long as you can turn whatever run out the stock has out before you get to the final diameter. Just like a 3 jaw.
But the repeatability is sooooo much better than a three jaw. More importantly, you don’t foul up the part finish with the collet.

Exactly. Aaaannd, the part doesn't deflect nearly as much as it does being in a 3 or 4 jaw.

Posted: **Wed Jul 10, 2024 1:22 am**

PING!

: IMG_2655.jpeg (289.76 KiB) Viewed 1146 times

Posted: **Wed Jul 10, 2024 12:17 pm**

What do you do when you get tired of having a "nightstand" and a "carry" pistol because you can't find a holster for your light-equipped pistol?

: 20240710_073532.jpg (2.44 MiB) Viewed 1139 times

Make a holster. It's crude, and the supplies are from Hobby Lobby, but it's IWB so nobody should see it and it seems to work.

: 20240710_073546.jpg (2.3 MiB) Viewed 1139 times

: 20240710_073555.jpg (2.19 MiB) Viewed 1139 times

It's based on a Wright Leatherworks Banshee.

: 20240710_073634.jpg (1.8 MiB) Viewed 1139 times

Now to sweat in it and get it broken in.

Posted: **Wed Jul 10, 2024 1:06 pm**

Winter skin tone and summer skin tone

Guns & Outdoors Forum

The last person to post in this thread don’t get nothing.

Re: The last person to post in this thread don’t get nothing.

Re: The last person to post in this thread don’t get nothing.

Re: The last person to post in this thread don’t get nothing.

Re: The last person to post in this thread don’t get nothing.

Re: The last person to post in this thread don’t get nothing.

Re: The last person to post in this thread don’t get nothing.

Re: The last person to post in this thread don’t get nothing.

Re: The last person to post in this thread don’t get nothing.

Re: The last person to post in this thread don’t get nothing.

Re: The last person to post in this thread don’t get nothing.

Re: The last person to post in this thread don’t get nothing.

Re: The last person to post in this thread don’t get nothing.

Re: The last person to post in this thread don’t get nothing.

Re: The last person to post in this thread don’t get nothing.

Re: The last person to post in this thread don’t get nothing.

Re: The last person to post in this thread don’t get nothing.

Re: The last person to post in this thread don’t get nothing.

Re: The last person to post in this thread don’t get nothing.

Re: The last person to post in this thread don’t get nothing.

Re: The last person to post in this thread don’t get nothing.

Re: The last person to post in this thread don’t get nothing.

Re: The last person to post in this thread don’t get nothing.

Re: The last person to post in this thread don’t get nothing.

Re: The last person to post in this thread don’t get nothing.

Re: The last person to post in this thread don’t get nothing.